Analysis of color volume of multi‐chromatic displays using gamut rings

There are claims that multi‐chromatic displays can achieve a wider color gamut by the use of additional highly saturated secondary color channels. However, there are other claims that these displays lose lightness and/or color saturation at brighter levels. These apparently divergent views have led to some controversy in the display industry and at standard setting organizations. This study examines the color gamut volume for a variety of simulated and measured multi‐chromatic (sometimes incorrectly referred to as “multi‐primary”) displays using combinations of white and/or secondary color channels, such as cyan, magenta, and yellow. Furthermore, a two‐dimensional gamut representation, referred to as “gamut rings,” is introduced to illustrate that the addition of nonprimary optical color channels to a trichromatic (RGB) display can result in a significant decrease in the chroma at higher lightness levels. The additional saturated color channels can increase the gamut volume only around their hues at darker levels. The results also confirm the validity of comparing the color light output and white light output for revealing the design trade‐offs between the high‐peak white and the color‐image brightness for multi‐chromatic displays.     

Microwave bandpass filter by feedback interference topology

This paper proposes a signal feedback interference topology to control the characteristics of a coupled line bandpass filter. Control is carried out by varying the ratio of the transmission line parameters of the forward and the feedback couplers. The topology produces a compact filter that does not require a complicated design or fabrication. The results of the insertion and return losses show that the feedback‐controlled design has desirable features in terms of the design frequency, fractional bandwidth, stopband rejection level, roll‐off rate and insertion loss. The test results of the fabricated prototype achieved good agreement with the simulation results of the ideal transmission line design model. Several microwave, modern wireless and mobile/satellite communication systems may benefit from such a filter design due to its compactness and flexibility.     

2-Aminobenzothiazoles Inhibit Virulence Gene Expression and Block Polymyxin Resistance in Salmonella enterica

One promising strategy to combat antibiotic-resistant bacteria is to develop compounds that block bacterial defenses against antibacterial conditions produced by the innate immune system. Salmonella enterica, which causes food-borne gastroenteritis and typhoid fever, requires histidine kinases (HKs) to resist innate immune defenses such as cationic antimicrobial peptides (CAMPs). Herein, we report that 2-aminobenzothiazoles block histidine kinase-dependent phenotypes in Salmonella enterica serotype Typhimurium. We found that 2-aminobenzothiazoles inhibited growth under low Mg²⁺, a stressful condition that requires histidine kinase-mediated responses, and decreased expression of the virulence genes pagC and pagK. Furthermore, we discovered that 2-aminobenzothiazoles weaken Salmonella’s resistance to polymyxin B and polymyxin E, which are last-line antibiotics and models for host defense CAMPs. These findings raise the possibilities that 2-aminobenzothiazoles can block HK-mediated bacterial defenses and can be used in combination with polymyxins to treat infections caused by Salmonella.     

基于ＰＩＤ控制算法的直流微网容错控制方法研究

构建直流微网容错控制对象模型，调节直流微电网的输出回路参数；以输出功率、直流微网的 参考电压、弱电网下系统惯性响应特征等为约束参量，构建直流微网容错控制目标函数，在不同电网强度下 进行直流微网容错控制的参数自整定性调节，采用无功环比例积分控制方法进行直流微网容错寻优分析， 建立模糊 ＰＩＤ控制模型，采用变结构的模糊 ＰＩＤ控制方法进行直流微网容错控制过程中的自适应加权学习 和误差反馈调节，实现直流微网容错控制改进设计。仿真结果表明，采用该方法进行直流微网控制的容错 性能较好，输出稳定性较强，具有较好的直流微网输出增益。     

基于CAN总线的多通道开度阀控制系统的设计

针对现有电动阀门控制系统可嵌入性差的问题，设计了一种基于CAN总线的网络化、多通道、开度型阀门嵌入式控制系统。其中，上位机主要用于下达各阀门开度等控制指令并同时监测其工作状态，而下位机采用双MCU架构，主MCU用于控制各阀门的开度大小，从MCU负责采集开度反馈电流以实现闭环控制。下位机采用了模糊PID算法进行控制参数的动态整定，可满足阀门在不同工况下的控制精度要求，并通过OLED屏显示各通道阀门的实际开度值。实验表明,该控制系统运行稳定，能实现对多通道开度阀的精准控制，控制精度在0.6%以内，并支持远程上位机控制和现地控制等多种工作模式。     

AlF3-modified LiCoPO4 for an advanced cathode towards high energy lithium-ion battery

Surface-interface reaction between the electrode and electrolyte plays a key role in lithium-ion storage properties, especially for high voltage cathode such as LiCoPO₄ and Ni-riched cathode. Generally, surface modification is an effective method to improve the electrochemical performance of electrode materials. Herein, in order to revise the LiCoPO₄ cathode with desirable properties, uniform AlF₃-modified LiCoPO₄ (LiCoPO₄@AlF₃) cathode materials in nano-sized distribution are synthesized. XRD result indicates that there is no structural transformation observed after AlF₃ coating. TEM characterization and XPS analysis reveal that the surface of LiCoPO₄ particle is coated by a nano-sized uniform AlF₃ layer. Further, the electrochemical results indicate that AlF₃ layer significantly improves the cycling and rate performances of LiCoPO₄ cathode within the voltage range of 3.0–5.0 V. After a series of optimization, 4 mol% AlF₃-coated LiCoPO₄ material exhibits the best properties including an initial discharge capacity of 159 mA h g^?1 at 0.1 C with 91% capacity retention after 50 cycles, especially a discharge capacity of 90 mA h g^?1 can be obtained at 1 C rate. CV curves indicate that the polarization of cathode is reduced by AlF₃ layer and EIS curves reveal that AlF₃ layer relieves the increase of resistance to facilitate Li-ion transfer at the interface between electrode and electrolyte during the cycling process. The enhanced electrochemical performances are attributed to that the AlF₃ layer can stabilize the interface between the cathode and electrolyte, form steady SEI film and suppress the electrolyte continuous decomposition at 5 V high voltages. This feasible strategy and novel characteristics of LiCoPO₄@AlF₃ could promise the prospective applications in the stat-art of special lithium-ion battery with high energy and/or power density.     

Structural,electrical, optical and dielectric properties of yttrium substituted cadmium ferrites prepared by Co-Precipitation method

The yttrium substituted cadmium ferrites having composition Cd_1-xY_xFe₂O₄ (X = 0.00, 0.125, 0.250, 0.375, 0.500) were synthesized by the co-precipitation method and sintered at 1100 °C for 6 h. Structural, morphological, electrical, optical and dielectric characteristics were explored by XRD, SEM, EDS, FTIR, I–V two probes, UV–Vis and LCR techniques.XRD results confirmed the cubic structure of spinel ferrites. A decrease in lattice constants of the prepared samples was observed with the substitution of Y ions and was attributed to the difference in ionic radii of Y³⁺ (0.95 Å) and Cd²⁺ (0.97 Å) ions. Cationic distributions, ionic radii of both tetrahedral and octahedral sites, tolerance factor, oxygen positional parameters, bond lengths, interatomic distances, positional parameters and bond length angles were calculated from XRD data. The morphology of the prepared ferrites was studied using SEM and results ratified the XRD results. EDS confirmed the presence of all inserted elements in Cd_1-xY_xFe₂O₄ composition. DC resistivity and drift mobility of soft-ferrites were found to be increased from 1.047 × 10⁸–4.822 × 10¹⁰ Ω-cm and 5.87 × 10⁻¹² – 1.045 × 10⁻¹⁴ cm²V⁻¹s⁻¹, respectively, at 523 K with yttrium content confirming the behavior of semiconductor materials. The optical band gap energy calculated from the UV–Vis pattern of the Cd_1-xY_xFe₂O₄ system was decreased from 3.6011 to 2.8153 eV. DC resistivity and optical band gaps exposed inverse relation. FTIR results revealed lower and upper-frequency absorption bands in the ranges of 419.31–417.01 cm⁻¹ and 540.95–565.70 cm⁻¹, respectively. Dielectric constant and dielectric losses were in decreasing order, while ac conductivity revealed rising behavior with increasing frequency. Results showed the potential of yttrium doped Cd nanoferrites for applications in high-frequency microwave absorbing devices.     

基于局部放电法的矿用高压电缆信号去噪算法研究

干扰噪声直接影响局部放电法有效检测矿用高压电缆故障。基于局部放电法，综合采用理论计算、仿真实验、现场试验的方法，对比分析了短时傅里叶变换和傅里叶分析去噪法的原理和优缺点，提出了一种矿用高压电缆的局部放电去噪算法——小波阈值去噪法，同时，选择了合理的阈值函数和去噪流程。基于此，采用白噪声和连续周期信号作为高压电缆的干扰噪声，进行了模拟仿真实验。结果表明，小波阈值去噪法可有效抑制白噪声，其中，Db2小波性能和去噪效果最好；同时，现场试验结果显示，去噪后信噪比得到了显著增加，验证了小波阈值去噪法的合理性和可靠性。     

Modification of structure and conductivity of nanohorns by toluene addition in carbon arc

Abstract

In the present work, we compare the structure and transport properties of carbon nanohorns (CNHs) synthesized by arc evaporation of graphite alone and with the addition of some portion of toluene. The materials have been investigated using transmission electron microscopy, Raman and infrared spectroscopies, thermogravimetric and BET analyses. The addition of a small amount of toluene during the evaporation of graphitic rod increases the length of CNHs, affects their hierarchical arrangement in aggregates and results in surface functionalization. All these features significantly enhance the conductivity of CNHs obtained with toluene additive in comparison with the pristine CNHs.     

The vibration and pull-in mechanism of two coupled elastically restrained beams assembly subjected to electrostatic force

ABSTRACT

The novel model of the coupled beam-type electrodes with elastic roots, subjected to the AC and DC voltages is constructed. The exact critical pull-in voltage of the two coupled elastically restrained beams with size effect is presented. The analytical method of the general system subjected to the AC and DC voltages simultaneously is presented. The characteristic mechanism of coupled vibration is investigated.